Operácie

Acrob004: Rozdiel medzi revíziami

Zo stránky SensorWiki

Balogh (diskusia | príspevky)
Bez shrnutí editace
Balogh (diskusia | príspevky)
Bez shrnutí editace
Riadok 1: Riadok 1:
[[Acrob003|< Previous]] | [[Acrob|Home]] | [[Acrob005|Next >]]
[[Acrob003|< Previous]] | [[Acrob|Home]] | [[Acrob005|Next >]]
== '''Pushbutton''' ==
To test the pushbutton, please connect one LED with current limiting resistor together with a pushbutton:
[[Obrázok:AcrobPushbutton01.jpg]]
This setup doesn't require microcontroller, it is just to test it and recognize its function, pinout and operation.
No program required!
Let's modify the circuit and try to measure the input with the microcontroller and display its value on the terminal.
Modify the connection according the following diagram and download the attached piece of software.
<source lang="c">
#define SWITCH 3                // select the pin for Switch
void setup()
{
Serial.begin(9600);
pinMode(SWITCH, INPUT );        // this pin is an INPUT
Serial.println("Button test:");
}
void loop()                      // endless loop
{
Serial.print("Input D3 = ");
Serial.println(digitalRead(SWITCH),BIN);
delay(250);                    // wait 1/4s for another
}
</source>
Another example uses the switch to control the LED. Exactly as in the first experiment, but now the controller makes the
decision.


<source lang="c">
<source lang="c">

Verzia z 14:20, 12. jún 2010

< Previous | Home | Next >


Pushbutton

To test the pushbutton, please connect one LED with current limiting resistor together with a pushbutton:

This setup doesn't require microcontroller, it is just to test it and recognize its function, pinout and operation. No program required!

Let's modify the circuit and try to measure the input with the microcontroller and display its value on the terminal. Modify the connection according the following diagram and download the attached piece of software.

#define SWITCH 3                 // select the pin for Switch

void setup()
{
 Serial.begin(9600);
 pinMode(SWITCH, INPUT );        // this pin is an INPUT
 Serial.println("Button test:");
}

void loop()                      // endless loop
{
 Serial.print("Input D3 = ");
 Serial.println(digitalRead(SWITCH),BIN);
 delay(250);                     // wait 1/4s for another
}


Another example uses the switch to control the LED. Exactly as in the first experiment, but now the controller makes the decision.

/*
  Button
 
 Turns on and off a light emitting diode(LED) connected to digital  
 pin 13, when pressing a pushbutton attached to pin 7. 
 
 
 The circuit:
 * LED attached from pin 13 to ground 
 * pushbutton attached to pin 2 from +5V
 * 10K resistor attached to pin 2 from ground
 
 * Note: on most Arduinos there is already an LED on the board
 attached to pin 13.
 
 
 created 2005
 by DojoDave <http://www.0j0.org>
 modified 17 Jun 2009
 by Tom Igoe
 
  http://www.arduino.cc/en/Tutorial/Button
 */

// constants won't change. They're used here to 
// set pin numbers:
const int buttonPin = 2;     // the number of the pushbutton pin
const int ledPin =  13;      // the number of the LED pin

// variables will change:
int buttonState = 0;         // variable for reading the pushbutton status

void setup() {
  // initialize the LED pin as an output:
  pinMode(ledPin, OUTPUT);      
  // initialize the pushbutton pin as an input:
  pinMode(buttonPin, INPUT);     
}

void loop(){
  // read the state of the pushbutton value:
  buttonState = digitalRead(buttonPin);

  // check if the pushbutton is pressed.
  // if it is, the buttonState is HIGH:
  if (buttonState == HIGH) {     
    // turn LED on:    
    digitalWrite(ledPin, HIGH);  
  } 
  else {
    // turn LED off:
    digitalWrite(ledPin, LOW); 
  }
}

< Previous | Home | Next >