|
|
| Riadok 1: |
Riadok 1: |
| − | Tento program pouzije PortD.4 (arduino D4) ako pocitadlo.
| |
| − | Mozne pripojit tlacitko, alebo 555 a pocitat pocet impulzov.
| |
| | | | |
| − | Vstavany terminal Arduina nema formatovanie, takze treba pouzit
| |
| − | iny terminal aby sa to pekne vypisovalo:
| |
| − |
| |
| − | <source lang="c">
| |
| − | #define SWITCH 5 // select the pin for Switch
| |
| − |
| |
| − | void setup()
| |
| − | {
| |
| − | pinMode(SWITCH, INPUT); // this pin is an INPUT
| |
| − | TCNT1 = 0x00; // initialize (CLEAR)counter
| |
| − | TCCR1B = 0x07; // T1 clk = external clock source on pin T1, rising edge
| |
| − |
| |
| − | Serial.begin(9600);
| |
| − | Serial.println("Button test:");
| |
| − | }
| |
| − |
| |
| − | void loop() // endless loop
| |
| − | {
| |
| − | Serial.print("Input D5 = ");
| |
| − | Serial.print(digitalRead(SWITCH),BIN);
| |
| − | Serial.print(" TCNT1 = ");
| |
| − | Serial.print(TCNT1,DEC);
| |
| − | Serial.print('\r'); // this will not work with embedded Serial Monitor,
| |
| − | // but works fine with e.g. putty terminal
| |
| − |
| |
| − | delay(250); // wait 1/4s for another measurement
| |
| − | }
| |
| − |
| |
| − | </source>
| |
| − |
| |
| − |
| |
| − |
| |
| − | [[Obrázok:AVR Timer T1 Counter.png|center]]
| |
| − |
| |
| − |
| |
| − |
| |
| − | [[Obrázok:AVR Timer TCNT1 Counter.png|center]]
| |
| − |
| |
| − |
| |
| − | Nasledovny kus programu nastavi pocitadlo na 5 impulzov pred pretecenim (0xFFFF - 5) a
| |
| − | potom sleduje v hlavnej slucke, kedy nastane pretecenie. Ako hodinky je pouzity externy
| |
| − | signal na T1, cize tlacitko alebo 555.
| |
| − |
| |
| − | <source lang="C">
| |
| − | /* Example 9.2. Timer counter 1 in timer mode - pooled version */
| |
| − |
| |
| − | #define SWITCH 5 // Arduino D5, ATmega328 PD.5
| |
| − | #define LED 13 // Arduino D13, ATmega328 PB.5
| |
| − |
| |
| − | int ledState = LOW; // variable used to store the last LED status, to toggle the light
| |
| − |
| |
| − | void setup() // run once, when the sketch starts
| |
| − | {
| |
| − | /* *********************** Init device ************************************ */
| |
| − |
| |
| − | pinMode(SWITCH, INPUT); // this pin is an INPUT
| |
| − | pinMode(LED, OUTPUT);
| |
| − |
| |
| − | Serial.begin(9600);
| |
| − | Serial.println("Timer T1 test:");
| |
| − |
| |
| − | TCCR1B = 0x07; // T1 clk = external clock source on pin T1, rising edge
| |
| − | TCCR1A = 0x00; // T1 in timer mode
| |
| − | TCNT1 = 0xFFFB; // initialize the counter (16-bit! Low+High bytes)
| |
| − | TIFR1 = 0x01; // (1<<TOV1); if a 1 is written to a TOV1 bit
| |
| − | // - the TOV1 bit will be cleared
| |
| − | }
| |
| − |
| |
| − | /* *********************** Main Loop ************************************** */
| |
| − |
| |
| − | void loop() // run over and over again
| |
| − | {
| |
| − | if ( (TIFR1 & 0x01) == 0x01) // If the overflow flag is set
| |
| − | {
| |
| − | ledState = !ledState; // toggle the status of the ledPin
| |
| − | digitalWrite(LED, ledState); // update the LED pin itself
| |
| − | TCNT1 = 0xFFFB; // Restart T1 - reload
| |
| − | TIFR1 = 0x01; // Clear the overflow flag
| |
| − | }
| |
| − | else
| |
| − | asm("nop"); // Do nothing
| |
| − |
| |
| − | Serial.print("Input D5 = ");
| |
| − | Serial.print(digitalRead(SWITCH),BIN);
| |
| − | Serial.print(" TCNT1 = ");
| |
| − | Serial.print(TCNT1,DEC);
| |
| − | Serial.print('\r'); // this will not work with embedded Serial Monitor,
| |
| − | // but works fine with e.g. putty terminal
| |
| − |
| |
| − | }
| |
| − |
| |
| − | </source>
| |