7-segmentový displej na futbal: Rozdiel medzi revíziami
Z SensorWiki
(→Overenie) |
(→Algoritmus a program) |
||
(20 medziľahlých úprav od rovnakého používateľa nie je zobrazených.) | |||
Riadok 1: | Riadok 1: | ||
− | Záverečný projekt predmetu MIPS / LS2024 - ''' | + | Záverečný projekt predmetu MIPS / LS2024 - '''Daniel Žula''' |
== Zadanie == | == Zadanie == | ||
− | + | Pripojenie 7 - segmentového LED displeja k vývojovej doske, vytvorenie potrebných knižníc a funkcií. Cieľom je, aby sme dokázali zobraziť skóre futbalového zápasu, ktoré dokážeme meniť podľa potreby pomocou tlačidiel. | |
[[Obrázok:ard.jpg|400px|thumb|center|Vývojová doska ACROB.]] | [[Obrázok:ard.jpg|400px|thumb|center|Vývojová doska ACROB.]] | ||
Riadok 10: | Riadok 10: | ||
'''Literatúra:''' | '''Literatúra:''' | ||
* [http://ap.urpi.fei.stuba.sk/sensorwiki/index.php/Acrob_technical_description Dokumentácia k doske Acrob] | * [http://ap.urpi.fei.stuba.sk/sensorwiki/index.php/Acrob_technical_description Dokumentácia k doske Acrob] | ||
− | |||
Riadok 17: | Riadok 16: | ||
== Analýza a opis riešenia == | == Analýza a opis riešenia == | ||
− | + | Princíp fungovania bol jednoduchý, ak stlačíme tlačidlo príslušné k prvému tímu, meníme skóre prvého tímu a ak stlačíme tlačidlo príslušné k druhému tímu, meníme skóre druhého tímu. Takisto máme tlačidlo RESET, ktoré celé skóre resetuje. Na správne fungovanie sme si vytvorili knižnicu, v ktorej sme zadefinovali čísla od 0-9 pomocou zapnutých a vypnutých segmentov na 7 segmentovke. | |
− | [[Súbor: | + | [[Súbor:TM1637-Display-Module-Parts.jpg|600px|thumb|center|TM1637 displej]] |
− | |||
− | [[Súbor: | + | [[Súbor:zapojenie_futbal.jpg|800px|thumb|center|Schéma zapojenia TM1637 7 segmentového displeja]] |
=== Algoritmus a program === | === Algoritmus a program === | ||
− | + | Tento program sme vytvorili na ovládanie 7 segmentového displeja pomocou tlačidiel a následného zobrazovania futbalového skóre pomocou tlačidiel. Najprv sme si vytvorili knižnicu do ktorej sme uložili čísla od 0-9 na zobrazenie čísiel pomocou svietiacich a zhasnutých segmentov. Následne sme si vytvorili funkcie na zapnutie a vypnutie komunikácie. | |
+ | |||
+ | Potom sme si vytvorili funkcie na inicializáciu, nastavenie segmentov a ich následné zobrazenie. Nakoniec sme pre INT0 a INT1 spravili funkcie, jedna pre ľavú stranu a druhá pre pravú stranu, v ktorých po stlačení tlačidla nastalo zvýšenie hodnoty o 1, kde ak sme dosiahli číslo 99 a zvýšili sme ho, číslo sa nám resetovalo naspäť na 0, keďže na číselné hodnoty sme mali iba 2 7 - segmentové displeje. Keď sme mali všetky tieto funkcie zadefinované, v hlavnej časti programu sme CLK aj DIO nastavili opäť ako input, povolili sme INT0 a INT1 takisto sei(). | ||
+ | |||
+ | Následne vo while funkcii sme už len dané čísla, ktoré boli uložené v counter_left a counter_right zobrazovali pomocou našej funkcie pre zobrazenie čísla na 7 segmentovke, kde sme pozíciu čísel nastavili na pravú 7 segmentovku z dvojice (čiže celkovo 2. a 4. 7 segmentovka) a po zvýšení čísla na 10 a viac sa začali využívať obe 7 segmentové displeje pre daný tím. Po stlačení tlačidla RESET sa hodnoty v counter_left a counter_right vynulovali a opäť sa využívali iba pravé 7 segmentovky z dvojice. Takto to funguje donekonečna. | ||
<tabs> | <tabs> | ||
− | <tab name=" | + | <tab name="SemProj"><source lang="c++" style="background: LightYellow;"> |
+ | #include <avr/io.h> | ||
+ | |||
+ | #define F_CPU 16000000UL // Define CPU frequency | ||
+ | |||
+ | // Required libraries | ||
+ | #include <stdio.h> | ||
#include <avr/io.h> | #include <avr/io.h> | ||
+ | #include <util/delay.h> | ||
+ | #include <avr/interrupt.h> | ||
+ | |||
+ | |||
+ | #define set_bit(ADDRESS,BIT) (ADDRESS |= (1<<BIT)) | ||
+ | #define clear_bit(ADDRESS,BIT) (ADDRESS &= ~(1<<BIT)) | ||
+ | |||
+ | #define CLK PD5 // CLK -> pin 5 portD.5 | ||
+ | #define DIO PD4 // DIO -> pin 4 portD.4 | ||
+ | |||
+ | #define LEFT_START_STOP_PIN PD2 // Left team score button | ||
+ | #define RIGHT_START_STOP_PIN PD3 // Right team score button | ||
+ | #define RESTART_PIN PD6 // Restart button | ||
+ | |||
+ | #define BIT_DELAY 100 // Delay 100ms | ||
+ | |||
+ | // Define for TM1637 | ||
+ | #define TM1637_I2C_COMM1 0x40 | ||
+ | #define TM1637_I2C_COMM2 0xC0 | ||
+ | #define TM1637_I2C_COMM3 0x80 | ||
+ | |||
+ | // 7-segment display digit mapping | ||
+ | const uint8_t digitToSegment[] = { | ||
+ | // XGFEDCBA | ||
+ | 0b00111111, // 0 | ||
+ | 0b00000110, // 1 | ||
+ | 0b01011011, // 2 | ||
+ | 0b01001111, // 3 | ||
+ | 0b01100110, // 4 | ||
+ | 0b01101101, // 5 | ||
+ | 0b01111101, // 6 | ||
+ | 0b00000111, // 7 | ||
+ | 0b01111111, // 8 | ||
+ | 0b01101111, // 9 | ||
+ | 0b01110111, // A | ||
+ | 0b01111100, // b | ||
+ | 0b00111001, // C | ||
+ | 0b01011110, // d | ||
+ | 0b01111001, // E | ||
+ | 0b01110001 // F | ||
+ | }; | ||
+ | |||
+ | static const uint8_t minusSegments = 0b01000000; | ||
+ | |||
+ | uint8_t brightness = (0x7 & 0x7) | 0x08; | ||
+ | |||
+ | int inicialize_bit(uint8_t byte){ | ||
+ | uint8_t data = byte; | ||
+ | |||
+ | // 8 Data Bits | ||
+ | for(uint8_t i = 0; i < 8; i++) { | ||
+ | // CLK low | ||
+ | set_bit(DDRD, CLK); | ||
+ | clear_bit(PORTD, CLK); | ||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | // Set data bit | ||
+ | if (data & 0x01){ | ||
+ | clear_bit(DDRD, DIO); // Set DIO as input | ||
+ | set_bit(PORTD, DIO); // DIO as input pull-up on | ||
+ | } else{ | ||
+ | set_bit(DDRD, DIO); // Set DIO as output | ||
+ | clear_bit(PORTD, DIO); // Set DIO low | ||
+ | } | ||
+ | |||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | // CLK high | ||
+ | clear_bit(DDRD, CLK); // Set CLK as input | ||
+ | set_bit(PORTD, CLK); // CLK as input pull-up on | ||
+ | _delay_us(BIT_DELAY); | ||
+ | data = data >> 1; | ||
+ | } | ||
+ | |||
+ | // Wait for acknowledge | ||
+ | // CLK to zero | ||
+ | set_bit(DDRD, CLK); // Set CLK as output | ||
+ | clear_bit(PORTD, CLK); // Set CLK low | ||
+ | |||
+ | clear_bit(DDRD, DIO); // Set DIO as input | ||
+ | set_bit(PORTD, DIO); // DIO as input pull-up on | ||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | // CLK to high | ||
+ | clear_bit(DDRD, CLK); // Set CLK as input | ||
+ | set_bit(PORTD, CLK); // Set CLK high | ||
+ | _delay_us(BIT_DELAY); | ||
+ | uint8_t ack = !bit_is_clear(PIND, DIO); | ||
+ | if (ack == 0) | ||
+ | set_bit(DDRD, DIO); // Set DIO as output | ||
+ | clear_bit(PORTD, DIO); // Set DIO low | ||
+ | |||
+ | _delay_us(BIT_DELAY); | ||
+ | set_bit(DDRD, CLK); // Set CLK as output | ||
+ | clear_bit(PORTD, CLK); // Set CLK low | ||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | return ack; | ||
+ | } | ||
− | + | ||
+ | void comunication_start(){ | ||
+ | set_bit(DDRD, DIO); // Set DIO as output | ||
+ | clear_bit(PORTD, DIO); // Set DIO as output | ||
+ | _delay_us(BIT_DELAY); | ||
+ | } | ||
+ | |||
+ | void comunication_stop(){ | ||
+ | set_bit(DDRD, DIO); // Set DIO as output | ||
+ | clear_bit(PORTD, DIO); // Set DIO as output | ||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | clear_bit(DDRD, CLK); // Set CLK as input | ||
+ | set_bit(PORTD, CLK); // CLK as input pull-up on | ||
+ | _delay_us(BIT_DELAY); | ||
+ | |||
+ | clear_bit(DDRD, DIO); // Set DIO as input | ||
+ | set_bit(PORTD, DIO); // DIO as input pull-up on | ||
+ | _delay_us(BIT_DELAY); | ||
+ | } | ||
+ | |||
+ | void set_segments(const uint8_t segments[], uint8_t length, uint8_t pos){ | ||
+ | // Write COMM1 | ||
+ | comunication_start(); | ||
+ | inicialize_bit(TM1637_I2C_COMM1); | ||
+ | comunication_stop(); | ||
+ | |||
+ | // Write COMM2 + first digit address | ||
+ | comunication_start(); | ||
+ | inicialize_bit(TM1637_I2C_COMM2 + (pos & 0x03)); | ||
+ | |||
+ | // Write the data bytes | ||
+ | for (uint8_t k=0; k < length; k++) | ||
+ | inicialize_bit(segments[k]); | ||
+ | |||
+ | comunication_stop(); | ||
+ | |||
+ | // Write COMM3 + brightness | ||
+ | comunication_start(); | ||
+ | inicialize_bit(TM1637_I2C_COMM3 + (brightness & 0x0f)); | ||
+ | comunication_stop(); | ||
+ | } | ||
+ | |||
+ | |||
+ | // Function to display a number in a given base with custom options | ||
+ | void display_number(int8_t base, uint16_t num, uint8_t dots, const int leading_zero, | ||
+ | uint8_t length, uint8_t pos) | ||
{ | { | ||
− | + | int negative = 0; // False | |
+ | if (base < 0) { | ||
+ | base = -base; | ||
+ | negative = 1; // True | ||
+ | } | ||
+ | |||
+ | uint8_t digits[4]; | ||
+ | |||
+ | if (num == 0 && !leading_zero) { | ||
+ | // Singular case - take care separately | ||
+ | for(uint8_t i = 0; i < (length-1); i++) | ||
+ | digits[i] = 0; | ||
+ | digits[length-1] = digitToSegment[0 & 0x0f];; | ||
+ | } | ||
+ | else { | ||
+ | for(int i = length-1; i >= 0; --i) | ||
+ | { | ||
+ | uint8_t digit = num % base; | ||
+ | |||
+ | if (digit == 0 && num == 0 && leading_zero == 0) | ||
+ | // Leading zero is blank | ||
+ | digits[i] = 0; | ||
+ | else | ||
+ | digits[i] = digitToSegment[digit & 0x0f];; | ||
+ | |||
+ | if (digit == 0 && num == 0 && negative) { | ||
+ | digits[i] = minusSegments; | ||
+ | negative = 0; | ||
+ | } | ||
+ | |||
+ | num /= base; | ||
+ | } | ||
+ | } | ||
+ | |||
+ | |||
+ | set_segments(digits, length, pos); | ||
+ | } | ||
+ | |||
+ | volatile uint8_t count_left = 0; // Counter for the left displays | ||
+ | volatile uint8_t count_right = 0; // Counter for the right displays | ||
− | |||
− | |||
− | |||
− | |||
− | + | ||
+ | // External interrupt 0 (button for the left team) | ||
+ | ISR (INT0_vect) | ||
+ | { | ||
+ | |||
+ | |||
+ | _delay_ms(10); | ||
+ | if(bit_is_clear(PIND, LEFT_START_STOP_PIN)){ | ||
+ | // Increase left count and reset if it reaches 100 | ||
+ | count_left++; | ||
+ | |||
+ | if (count_left >= 100) count_left = 0; | ||
+ | } | ||
+ | _delay_ms(150); | ||
} | } | ||
− | + | // External interrupt 1 (button for the right team) | |
− | + | ISR (INT1_vect) | |
− | + | { | |
+ | _delay_ms(10); | ||
+ | if(bit_is_clear(PIND, RIGHT_START_STOP_PIN)){ | ||
+ | // Increase right count and reset if it reaches 100 | ||
+ | count_right++; | ||
+ | if (count_right >= 100) count_right = 0; | ||
+ | } | ||
+ | _delay_ms(150); | ||
+ | } | ||
+ | |||
+ | |||
+ | int main(void){ | ||
+ | |||
+ | clear_bit(DDRD, CLK); // Set CLK as input | ||
+ | set_bit(PORTD, CLK); // CLK as input pull-up on | ||
+ | |||
+ | clear_bit(DDRD, DIO); // Set DIO as input | ||
+ | set_bit(PORTD, DIO); // DIO as input pull-up o | ||
+ | |||
+ | clear_bit(DDRD, LEFT_START_STOP_PIN); // Set LEFT_START_STOP_PIN as input | ||
+ | set_bit(PORTD, LEFT_START_STOP_PIN); // LEFT_START_STOP_PIN as input pull-up on | ||
+ | |||
+ | clear_bit(DDRD, RIGHT_START_STOP_PIN); // Set RIGHT_START_STOP_PIN as input | ||
+ | set_bit(PORTD, RIGHT_START_STOP_PIN); // RIGHT_START_STOP_PIN as input pull-up on | ||
+ | |||
+ | clear_bit(DDRD, RESTART_PIN); // set RESET_PIN as input | ||
+ | set_bit(PORTD, RESTART_PIN); // RESET_PIN as input pull-up on | ||
+ | |||
+ | uint8_t data[] = { 0, 0, 0, 0 }; | ||
+ | set_segments(data, 4, 0); | ||
+ | |||
+ | |||
+ | EIMSK = 0b00000011; // Enable INT0, INT1 | ||
+ | EICRA = 0b00001010; // Detect falling edge on both pins | ||
+ | |||
+ | sei(); // Enable interrupts | ||
+ | |||
+ | set_bit(DDRB, PB5); | ||
+ | |||
+ | while (1) { | ||
+ | if (bit_is_clear(PIND, RESTART_PIN)) { | ||
+ | // Perform reset operation | ||
+ | |||
+ | count_left = 0; // Reset the left count | ||
+ | count_right = 0; // Reset the right count | ||
+ | |||
+ | } | ||
− | + | // Display left count on left two displays and right count on right two displays | |
+ | |||
+ | display_number_segment(count_right, 0, 2, 2); | ||
+ | |||
+ | display_number_segment(count_left, 0, 2, 0); | ||
− | + | } | |
− | </source></tab> | + | |
+ | return 0; | ||
+ | } | ||
+ | }</source></tab> | ||
</tabs> | </tabs> | ||
− | |||
− | |||
Zdrojový kód: [[Médiá:projektMenoPriezvisko.zip|zdrojaky.zip]] | Zdrojový kód: [[Médiá:projektMenoPriezvisko.zip|zdrojaky.zip]] | ||
− | |||
=== Overenie === | === Overenie === | ||
− | Na | + | Na zobrazovanie aktuálneho skóre používame dve tlačidlá, jedným, ktorý je vľavo meníme skóre tímu vľavo, a druhým, ktorý je v strede meníme skóre tímu ktorý je napravo, posledným tlačidlom ktoré je vpravo skóre resetujeme. |
− | |||
− | [[Súbor:projektfoto.jpg|400px|thumb|center| | + | [[Súbor:projektfoto.jpg|400px|thumb|center|Zapojenie 7 - segmentového displeja pre zobrazenie futbalového skóre spolu s tlačidlami]] |
'''Video:''' | '''Video:''' | ||
− | <center><youtube> | + | <center><youtube>nTv-t7sA78s</youtube></center> |
− | |||
− | |||
[[Category:AVR]] [[Category:MIPS]] | [[Category:AVR]] [[Category:MIPS]] |
Verzia zo dňa a času 08:52, 4. máj 2024
Záverečný projekt predmetu MIPS / LS2024 - Daniel Žula
Zadanie
Pripojenie 7 - segmentového LED displeja k vývojovej doske, vytvorenie potrebných knižníc a funkcií. Cieľom je, aby sme dokázali zobraziť skóre futbalového zápasu, ktoré dokážeme meniť podľa potreby pomocou tlačidiel.
Literatúra:
Analýza a opis riešenia
Princíp fungovania bol jednoduchý, ak stlačíme tlačidlo príslušné k prvému tímu, meníme skóre prvého tímu a ak stlačíme tlačidlo príslušné k druhému tímu, meníme skóre druhého tímu. Takisto máme tlačidlo RESET, ktoré celé skóre resetuje. Na správne fungovanie sme si vytvorili knižnicu, v ktorej sme zadefinovali čísla od 0-9 pomocou zapnutých a vypnutých segmentov na 7 segmentovke.
Algoritmus a program
Tento program sme vytvorili na ovládanie 7 segmentového displeja pomocou tlačidiel a následného zobrazovania futbalového skóre pomocou tlačidiel. Najprv sme si vytvorili knižnicu do ktorej sme uložili čísla od 0-9 na zobrazenie čísiel pomocou svietiacich a zhasnutých segmentov. Následne sme si vytvorili funkcie na zapnutie a vypnutie komunikácie.
Potom sme si vytvorili funkcie na inicializáciu, nastavenie segmentov a ich následné zobrazenie. Nakoniec sme pre INT0 a INT1 spravili funkcie, jedna pre ľavú stranu a druhá pre pravú stranu, v ktorých po stlačení tlačidla nastalo zvýšenie hodnoty o 1, kde ak sme dosiahli číslo 99 a zvýšili sme ho, číslo sa nám resetovalo naspäť na 0, keďže na číselné hodnoty sme mali iba 2 7 - segmentové displeje. Keď sme mali všetky tieto funkcie zadefinované, v hlavnej časti programu sme CLK aj DIO nastavili opäť ako input, povolili sme INT0 a INT1 takisto sei().
Následne vo while funkcii sme už len dané čísla, ktoré boli uložené v counter_left a counter_right zobrazovali pomocou našej funkcie pre zobrazenie čísla na 7 segmentovke, kde sme pozíciu čísel nastavili na pravú 7 segmentovku z dvojice (čiže celkovo 2. a 4. 7 segmentovka) a po zvýšení čísla na 10 a viac sa začali využívať obe 7 segmentové displeje pre daný tím. Po stlačení tlačidla RESET sa hodnoty v counter_left a counter_right vynulovali a opäť sa využívali iba pravé 7 segmentovky z dvojice. Takto to funguje donekonečna.
#include <avr/io.h>
#define F_CPU 16000000UL // Define CPU frequency
// Required libraries
#include <stdio.h>
#include <avr/io.h>
#include <util/delay.h>
#include <avr/interrupt.h>
#define set_bit(ADDRESS,BIT) (ADDRESS |= (1<<BIT))
#define clear_bit(ADDRESS,BIT) (ADDRESS &= ~(1<<BIT))
#define CLK PD5 // CLK -> pin 5 portD.5
#define DIO PD4 // DIO -> pin 4 portD.4
#define LEFT_START_STOP_PIN PD2 // Left team score button
#define RIGHT_START_STOP_PIN PD3 // Right team score button
#define RESTART_PIN PD6 // Restart button
#define BIT_DELAY 100 // Delay 100ms
// Define for TM1637
#define TM1637_I2C_COMM1 0x40
#define TM1637_I2C_COMM2 0xC0
#define TM1637_I2C_COMM3 0x80
// 7-segment display digit mapping
const uint8_t digitToSegment[] = {
// XGFEDCBA
0b00111111, // 0
0b00000110, // 1
0b01011011, // 2
0b01001111, // 3
0b01100110, // 4
0b01101101, // 5
0b01111101, // 6
0b00000111, // 7
0b01111111, // 8
0b01101111, // 9
0b01110111, // A
0b01111100, // b
0b00111001, // C
0b01011110, // d
0b01111001, // E
0b01110001 // F
};
static const uint8_t minusSegments = 0b01000000;
uint8_t brightness = (0x7 & 0x7) | 0x08;
int inicialize_bit(uint8_t byte){
uint8_t data = byte;
// 8 Data Bits
for(uint8_t i = 0; i < 8; i++) {
// CLK low
set_bit(DDRD, CLK);
clear_bit(PORTD, CLK);
_delay_us(BIT_DELAY);
// Set data bit
if (data & 0x01){
clear_bit(DDRD, DIO); // Set DIO as input
set_bit(PORTD, DIO); // DIO as input pull-up on
} else{
set_bit(DDRD, DIO); // Set DIO as output
clear_bit(PORTD, DIO); // Set DIO low
}
_delay_us(BIT_DELAY);
// CLK high
clear_bit(DDRD, CLK); // Set CLK as input
set_bit(PORTD, CLK); // CLK as input pull-up on
_delay_us(BIT_DELAY);
data = data >> 1;
}
// Wait for acknowledge
// CLK to zero
set_bit(DDRD, CLK); // Set CLK as output
clear_bit(PORTD, CLK); // Set CLK low
clear_bit(DDRD, DIO); // Set DIO as input
set_bit(PORTD, DIO); // DIO as input pull-up on
_delay_us(BIT_DELAY);
// CLK to high
clear_bit(DDRD, CLK); // Set CLK as input
set_bit(PORTD, CLK); // Set CLK high
_delay_us(BIT_DELAY);
uint8_t ack = !bit_is_clear(PIND, DIO);
if (ack == 0)
set_bit(DDRD, DIO); // Set DIO as output
clear_bit(PORTD, DIO); // Set DIO low
_delay_us(BIT_DELAY);
set_bit(DDRD, CLK); // Set CLK as output
clear_bit(PORTD, CLK); // Set CLK low
_delay_us(BIT_DELAY);
return ack;
}
void comunication_start(){
set_bit(DDRD, DIO); // Set DIO as output
clear_bit(PORTD, DIO); // Set DIO as output
_delay_us(BIT_DELAY);
}
void comunication_stop(){
set_bit(DDRD, DIO); // Set DIO as output
clear_bit(PORTD, DIO); // Set DIO as output
_delay_us(BIT_DELAY);
clear_bit(DDRD, CLK); // Set CLK as input
set_bit(PORTD, CLK); // CLK as input pull-up on
_delay_us(BIT_DELAY);
clear_bit(DDRD, DIO); // Set DIO as input
set_bit(PORTD, DIO); // DIO as input pull-up on
_delay_us(BIT_DELAY);
}
void set_segments(const uint8_t segments[], uint8_t length, uint8_t pos){
// Write COMM1
comunication_start();
inicialize_bit(TM1637_I2C_COMM1);
comunication_stop();
// Write COMM2 + first digit address
comunication_start();
inicialize_bit(TM1637_I2C_COMM2 + (pos & 0x03));
// Write the data bytes
for (uint8_t k=0; k < length; k++)
inicialize_bit(segments[k]);
comunication_stop();
// Write COMM3 + brightness
comunication_start();
inicialize_bit(TM1637_I2C_COMM3 + (brightness & 0x0f));
comunication_stop();
}
// Function to display a number in a given base with custom options
void display_number(int8_t base, uint16_t num, uint8_t dots, const int leading_zero,
uint8_t length, uint8_t pos)
{
int negative = 0; // False
if (base < 0) {
base = -base;
negative = 1; // True
}
uint8_t digits[4];
if (num == 0 && !leading_zero) {
// Singular case - take care separately
for(uint8_t i = 0; i < (length-1); i++)
digits[i] = 0;
digits[length-1] = digitToSegment[0 & 0x0f];;
}
else {
for(int i = length-1; i >= 0; --i)
{
uint8_t digit = num % base;
if (digit == 0 && num == 0 && leading_zero == 0)
// Leading zero is blank
digits[i] = 0;
else
digits[i] = digitToSegment[digit & 0x0f];;
if (digit == 0 && num == 0 && negative) {
digits[i] = minusSegments;
negative = 0;
}
num /= base;
}
}
set_segments(digits, length, pos);
}
volatile uint8_t count_left = 0; // Counter for the left displays
volatile uint8_t count_right = 0; // Counter for the right displays
// External interrupt 0 (button for the left team)
ISR (INT0_vect)
{
_delay_ms(10);
if(bit_is_clear(PIND, LEFT_START_STOP_PIN)){
// Increase left count and reset if it reaches 100
count_left++;
if (count_left >= 100) count_left = 0;
}
_delay_ms(150);
}
// External interrupt 1 (button for the right team)
ISR (INT1_vect)
{
_delay_ms(10);
if(bit_is_clear(PIND, RIGHT_START_STOP_PIN)){
// Increase right count and reset if it reaches 100
count_right++;
if (count_right >= 100) count_right = 0;
}
_delay_ms(150);
}
int main(void){
clear_bit(DDRD, CLK); // Set CLK as input
set_bit(PORTD, CLK); // CLK as input pull-up on
clear_bit(DDRD, DIO); // Set DIO as input
set_bit(PORTD, DIO); // DIO as input pull-up o
clear_bit(DDRD, LEFT_START_STOP_PIN); // Set LEFT_START_STOP_PIN as input
set_bit(PORTD, LEFT_START_STOP_PIN); // LEFT_START_STOP_PIN as input pull-up on
clear_bit(DDRD, RIGHT_START_STOP_PIN); // Set RIGHT_START_STOP_PIN as input
set_bit(PORTD, RIGHT_START_STOP_PIN); // RIGHT_START_STOP_PIN as input pull-up on
clear_bit(DDRD, RESTART_PIN); // set RESET_PIN as input
set_bit(PORTD, RESTART_PIN); // RESET_PIN as input pull-up on
uint8_t data[] = { 0, 0, 0, 0 };
set_segments(data, 4, 0);
EIMSK = 0b00000011; // Enable INT0, INT1
EICRA = 0b00001010; // Detect falling edge on both pins
sei(); // Enable interrupts
set_bit(DDRB, PB5);
while (1) {
if (bit_is_clear(PIND, RESTART_PIN)) {
// Perform reset operation
count_left = 0; // Reset the left count
count_right = 0; // Reset the right count
}
// Display left count on left two displays and right count on right two displays
display_number_segment(count_right, 0, 2, 2);
display_number_segment(count_left, 0, 2, 0);
}
return 0;
}
}
Zdrojový kód: zdrojaky.zip
Overenie
Na zobrazovanie aktuálneho skóre používame dve tlačidlá, jedným, ktorý je vľavo meníme skóre tímu vľavo, a druhým, ktorý je v strede meníme skóre tímu ktorý je napravo, posledným tlačidlom ktoré je vpravo skóre resetujeme.
Video: